View 5962-8957103KPA_804231.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Hermetically Sealed, Very High Speed, Logic Gate Optocouplers Technical Data
HCPL-540X* HCPL-643X 5962-89570 5962-89571 HCPL-543X
*See matrix for available extensions.
Features
* Dual Marked with Device Part Number and DSCC Standard Microcircuit Drawing * Manufactured and Tested on a MIL-PRF-38534 Certified Line * QML-38534, Class H and K * Three Hermetically Sealed Package Configurations * Performance Guaranteed over -55C to +125C * High Speed: 40 M bit/s * High Common Mode Rejection 500 V/s Guaranteed * 1500 Vdc Withstand Test Voltage * Active (Totem Pole) Outputs * Three Stage Output Available * High Radiation Immunity * HCPL-2400/30 Function Compatibility * Reliability Data * Compatible with TTL, STTL, LSTTL, and HCMOS Logic Families
* Computer-Peripheral Interfaces * Switching Power Supplies * Isolated Bus Driver (Networking Applications)(5400/1/K Only) * Pulse Transformer Replacement * Ground Loop Elimination * Harsh Industrial Environments * High Speed Disk Drive I/O * Digital Isolation for A/D, D/A Conversion
Each channel contains an AlGaAs light emitting diode which is optically coupled to an integrated high gain photon detector. This combination results in very high
Truth Tables
(Positive Logic) Multichannel Devices Input Output On (H) L Off (L) H
Description
These units are single and dual channel, hermetically sealed optocouplers. The products are capable of operation and storage over the full military temperature range and can be purchased as either standard product or with full MIL-PRF-38534 Class Level H or K testing or from the appropriate DSCC Drawing. All devices are manufactured and tested on a MIL-PRF-38534 certified line and are included in the DSCC Qualified Manufacturers List, QML-38534 for Hybrid Microcircuits.
Single Channel DIP Input Enable On (H) L Off (L) L On (H) H Off (L) H
Output L H Z Z
Functional Diagram
Multiple Channel Devices Available
VCC VE
Applications
* Military and Space * High Reliability Systems * Transportation, Medical, and Life Critical Systems * Isolation of High Speed Logic Systems
VO GND
The connection of a 0.1 F bypass capacitor between VCC and GND is recommended.
CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.
2
data rate capability. The detector has a threshold with hysteresis, which typically provides 0.25 mA of differential mode noise immunity and minimizes the potential for output signal chatter. The detector in the single channel units has a three state output stage which eliminates the need for a pull-up resistor and allows for direct drive of a data bus. All units are compatible with TTL, STTL, LSTTL, and HCMOS logic families. The 35 ns pulse width distortion specification guarantees a 10 MBd signaling rate at +125C with 35% pulse width
distortion. Figures 13 through 16 show recommended circuits for reducing pulse width distortion and optimizing the signal rate of the product. Package styles for these parts are 8 pin DIP through hole (case outlines P), and leadless ceramic chip carrier (case outline 2). Devices may be purchased with a variety of lead bend and plating options. See Selection Guide Table for details. Standard Microcircuit Drawing (SMD) parts are available for each package and lead style. Because the same electrical die (emitters and detectors) are used for each channel of each device
listed in this data sheet, absolute maximum ratings, recommended operating conditions, electrical specifications, and performance characteristics shown in the figures are similar for all parts. Occasional exceptions exist due to package variations and limitations and are as noted. Additionally, the same package assembly processes and materials are used in all devices. These similarities give justification for the use of data obtained from one part to represent other part's performance for die related reliability and certain limited radiation test results.
Selection Guide-Package Styles and Lead Configuration Options
Package Lead Style Channels Common Channel Wiring Agilent Part # & Options Commercial MIL-PRF-38534, Class H MIL-PRF-38534, Class K Standard Lead Finish Solder Dipped Butt Cut/Gold Plate Gull Wing/Soldered Class H SMD Part # Prescript for all below Either Gold or Solder Gold Plate Solder Dipped Butt Cut/Gold Plate Butt Cut/Soldered Gull Wing/Soldered Class K SMD Part # Prescript for all below Either Gold of Solder Gold Plate Solder Dipped Butt Cut/Gold Plate Butt Cut/Soldered Gull Wing/Soldered 8 Pin DIP Through Hole 1 None 8 Pin DIP Through Hole 2 VCC , GND 20 Pad LCCC Surface Mount 2 None
HCPL-5400 HCPL-5401 HCPL-540K Gold Plate Option #200 Option #100 Option #300 59628957001PX 8957001PC 8957001PA 8957001YC 8957001YA 8957001XA 59628957002KPX 8957002KPC 8957002KPA 8957002KYC 8957002KYA 8957002KXA
HCPL-5430 HCPL-5431 HCPL-543K Gold Plate Option #200 Option #100 Option #300 59628957101PX 8957101PC 8957101PA 8957101YC 8957101YA 8957101XA 59628957103KPX 8957103KPC 8957103KPA 8957103KYC 8957103KYA 8957103KXA
HCPL-6430 HCPL-6431 HCPL-643K Solder Pads
596289571022X 89571022A
59628957104K2X 8957104K2A
3
Functional Diagrams
8 Pin DIP Through Hole 1 Channel 8 Pin DIP Through Hole 2 Channels 20 Pad LCCC Surface Mount 2 Channels
15 VCC2 19
7 VO2 6 5
1 2 3 4
VCC VE
8 7 6 5
1 2 3 4
VCC VO1
8
VO2 GND2 VO1 GND1 7 8 VCC1
13 12
20
VO GND
2 3
10
GND
Note: All DIP devices have common VCC and ground. LCCC (leadless ceramic chip carrier) package has isolated channels with separate VCC and ground connections.
Outline Drawings
20 Terminal LCCC Surface Mount, 2 Channels
8.70 (0.342) 9.10 (0.358) 4.95 (0.195) 5.21 (0.205) 1.78 (0.070) 2.03 (0.080) 1.02 (0.040) (3 PLCS) 1.14 (0.045) 1.40 (0.055) 8.70 (0.342) 9.10 (0.358) 4.95 (0.195) 5.21 (0.205) 1.78 (0.070) 2.03 (0.080) 0.64 (0.025) (20 PLCS) 1.52 (0.060) 2.03 (0.080)
TERMINAL 1 IDENTIFIER 2.16 (0.085) METALLIZED CASTILLATIONS (20 PLCS) 0.51 (0.020)
NOTE: DIMENSIONS IN MILLIMETERS (INCHES). SOLDER THICKNESS 0.127 (0.005) MAX.
8 Pin DIP Through Hole, 1 and 2 Channel
9.40 (0.370) 9.91 (0.390) 0.76 (0.030) 1.27 (0.050) 4.32 (0.170) MAX. 8.13 (0.320) MAX. 7.16 (0.282) 7.57 (0.298)
0.51 (0.020) MIN.
3.81 (0.150) MIN.
0.20 (0.008) 0.33 (0.013)
2.29 (0.090) 2.79 (0.110)
0.51 (0.020) MAX. NOTE: DIMENSIONS IN MILLIMETERS (INCHES).
7.36 (0.290) 7.87 (0.310)
4
Leaded Device Marking
Agilent DESIGNATOR Agilent P/N DSCC SMD* DSCC SMD* PIN ONE/ ESD IDENT A QYYWWZ XXXXXX XXXXXXX XXX XXX * 50434 COMPLIANCE INDICATOR,* DATE CODE, SUFFIX (IF NEEDED) COUNTRY OF MFR. Agilent CAGE CODE*
Leadless Device Marking
Agilent DESIGNATOR Agilent P/N PIN ONE/ ESD IDENT COUNTRY OF MFR. A QYYWWZ XXXXXX * XXXX XXXXXX XXX 50434 * QUALIFIED PARTS ONLY COMPLIANCE INDICATOR,* DATE CODE, SUFFIX (IF NEEDED) DSCC SMD* DSCC SMD* Agilent CAGE CODE*
* QUALIFIED PARTS ONLY
Hermetic Optocoupler Options
Option 100 Description Surface mountable hermetic optocoupler with leads trimmed for butt joint assembly. This option is available on commercial and hi-rel product in 8 pin DIP (see drawings below for details).
4.32 (0.170) MAX.
0.51 (0.020) MIN. 2.29 (0.090) 2.79 (0.110)
1.14 (0.045) 1.40 (0.055) 0.51 (0.020) MAX. NOTE: DIMENSIONS IN MILLIMETERS (INCHES).
0.20 (0.008) 0.33 (0.013) 7.36 (0.290) 7.87 (0.310)
200
300
Lead finish is solder dipped rather than gold plated. This option is available on commercial and hi-rel product in 8 pin DIP. DSCC Drawing part numbers contain provisions for lead finish. All leadless chip carrier devices are delivered with solder dipped terminals as a standard feature. Surface mountable hermetic optocoupler with leads cut and bent for gull wing assembly. This option is available on commercial and hi-rel product in 8 pin DIP (see drawings below for details). This option has solder dipped leads.
4.57 (0.180) MAX. 0.20 (0.008) 0.33 (0.013) 9.65 (0.380) 9.91 (0.390)
4.57 (0.180) MAX.
0.51 (0.020) MIN. 2.29 (0.090) 2.79 (0.110)
1.40 (0.055) 1.65 (0.065) 0.51 (0.020) MAX.
5 MAX.
NOTE: DIMENSIONS IN MILLIMETERS (INCHES).
5
Absolute Maximum Ratings
(No derating required up to +125C) Storage Temperature Range, TS .................................. -65C to +150C Operating Temperature, TA ......................................... -55C to +125C Case Temperature, TC ................................................................ +170C Junction Temperature, TJ .......................................................... +175C Lead Solder Temperature .............................................. 260C for 10 s Average Forward Current, IF AVG (each channel) ........................ 10 mA Peak Input Current, IF PK (each channel) ............................... 20 mA[1] Reverse Input Voltage, VR (each channel) ....................................... 3 V Supply Voltage, VCC ............................................. 0.0 V min., 7.0 V max. Average Output Current, IO ............................ -25 mA min., 25 mA max. (each channel) Output Voltage, VO (each channel) ..................... -0.5 V min., 10 V max. Output Power Dissipation, PO (each channel) ........................... 130 mW Package Power Dissipation, PD (each channel) ......................... 200 mW
Single Channel Product Only
Three State Enable Voltage, VE ........................... -0.5 V min., 10 V max.
8 Pin Ceramic DIP Single Channel Schematic
ANODE
VE VO CATHODE
Note enable pin 7. An external 0.01 F to 0.1 F bypass capacitor must be connected between VCC and ground for each package type.
ESD Classification
(MIL-STD-883, Method 3015) HCPL-5400/01/0K ............................................................ ( ), Class 2 HCPL-5430/31/3K and HCPL-6430/31/3K ....................... (Dot), Class 3
Recommended Operating Conditions
Parameter Input Current (High) Supply Voltage, Output Input Voltage (Low) Fan Out (Each Channel) Symbol IF(ON) VCC VF(OFF) N Min. 6 4.75 - - Max. 10 5.25 0.7 5 Units mA V V TTL Loads
Single Channel Product Only High Level Enable Voltage VEH Low Level Enable Voltage VEL
2.0 0
VCC 0.8
V V
6
Electrical Characteristics
TA = -55C to +125C, 4.75 V VCC 5.25 V, 6 mA IF(ON) 10 mA, 0 V VF(OFF) 0.7 V, unless otherwise specified.
Limits Group A[10] Parameter Sym. Test Conditions Subgroups Min. Typ.* Max. Units Fig. Low Level Output Voltage VOL IOL = 8.0 mA (5 TTL Loads) 1, 2, 3 0.3 0.5 V 1 High Level Output Voltage VOH IOH = -4.0 mA 1, 2, 3 2.4 V 2 Output Leakage Current IOHH VO = 5.25 V, VF = 0.7 V 1, 2, 3 100 A Logic High Single ICCH VCC = 5.25 V, VE = 0 V 1, 2, 3 17 26 mA Supply Channel (Single Channel Only) Current Dual Channel 34 52 Logic Low Supply Current Single Channel ICCL 1, 2, 3 19 38 1.35 4.8 26 52 1.85 mA 13 9 9 2, 3 5, 6, 7 5, 6, 7 5, 6, 7 11 11 4, 9 4, 9 4, 9 5, 9, 11 5, 9, 11 Notes 9 9 9
13
Dual Channel Input Forward Voltage Input Reverse Breakdown Voltage Input-Output Insulation Leakage Current Propagation Delay Time Logic Low Output Propagation Delay Time Logic High Output
VF VR II-O tPHL tPLH
IF = 10 mA IR = 10 A VI-O = 1500 Vdc, RH = 45%, t=5s
1, 2, 3 1, 2, 3 1 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11
1.0 3.0
V V A ns ns ns V/s V/s
4
1.0 33 30 3 500 500 3000 3000 60 60 35
Pulse Width PWD Distortion Logic High Common |CMH| VCM = 50 VP-P, IF = 0 mA Mode Transient Immunity Logic Low Common |CML| VCM = 50 VP-P, IF = 6 mA Mode Transient Immunity
Single Channel Product Only
Parameter Logic High Enable Voltage Logic Low Enable Voltage Logic High Enable Current Logic Low Enable Current High Impedance State Supply Current High Impedance State Output Current Sym. VEH VEL IEH IEL ICCZ IOZL IOZH VE = 2.4 V VE = 5.25 V VE = 0.4 V VCC = 5.25 V, VE = 5.25 V VO = 0.4 V, VE = 2 V VO = 2.4 V, VE = 2 V VO = 5.25 V, VE = 2 V Test Conditions Limits Group A[10] Subgroups Min. Typ.* Max. Units Fig. 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 2.0 0.8 20 100 -0.4 28 -20 20 100 Notes
V
V A mA mA A
-0.28 22
*All typical values are at VCC = 5 V, TA = 25C, I F = 8 mA except where noted.
7
Typical Characteristics
All typical values are at TA = 25C, VCC = 5 V, IF = 8 mA, unless otherwise specified. Parameter Input Current Hysteresis Input Diode Temperature Coefficient Resistance (Input-Output) Capacitance (Input-Output) Logic Low Short Circuit Output Current Logic High Short Circuit Output Current Output Rise Time (10-90%) Output Fall Time (90-10%) Propagation Delay Skew Power Supply Noise Immunity Symbol IHYS VF TA RI-O CI-O IOSL IOSH tr tf tPSK PSNI Typ. 0.25 -1.11 1012 0.6 65 -50 15 10 30 0.5 Units mA mV/C pF mA mA ns ns ns VP-P Test Conditions VCC = 5 V IF = 10 mA VI-O = 500 V f = 1 MHz, VI-O = 0 V VO = VCC = 5.25 V, IF = 10 mA VCC = 5.25 V, IF = 0 mA, VO = GND 5 5 10 48 Hz fac 50 MHz Fig. 3 4 Notes
2 2 6, 9 6, 9
12 7
Single Channel Product Only Parameter Input Capacitance Output Enable Time to Logic High Output Enable Time to Logic Low Output Disable Time from Logic High Output Disable Time from Logic Low
Symbol CIN tPZH tPZL tPHZ tPLZ
Typ. Units Test Conditions 15 pF f = 1 MHz, VF = 0 V, Pins 2 and 3 15 ns 30 ns 20 ns 15 ns
Fig. Notes
8, 9 8, 9 8, 9 8, 9
Dual and Quad Channel Product Only Input Capacitance Input-Input Leakage Current Input-Input Resistance Input-Input Capacitance
CIN II-I RI-I C I-I
15 0.5 1012 1.3
pF nA pF
f = 1 MHz, VO = 0 V RH = 45%, VI-I = 500 Vdc VI-I = 500 V f = 1 MHz, VF = 0 V
8 8 8
8
Notes: 1. Not to exceed 5% duty factor, not to exceed 50 sec pulse width. 2. All devices are considered two-terminal devices: measured between all input leads or terminals shorted together and all output leads or terminals shorted together. 3. This is a momentary withstand test, not an operating condition. 4. tPHL propagation delay is measured from the 50% point on the rising edge of the input current pulse to the 1.5 V point on the falling edge of the output pulse. The tPLH propagation delay is measured from the 50% point on the falling edge of the input current pulse to the 1.5 V point on the rising edge of the output pulse. Pulse Width Distortion, PWD = |tPHL - t PLH|. 5. CML is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic low state (VO(MAX) < 0.8 V). CMH is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic high state (VO(MIN) > 2.0 V). 6. Duration of output short circuit time not to exceed 10 ms. 7. Power Supply Noise Immunity is the peak to peak amplitude of the ac ripple voltage on the VCC line that the device will withstand and still remain in the desired logic state. For desired logic high state, VOH(MIN) > 2.0 V, and for desired logic low state, VOL(MAX) < 0.8 V. 8. Measured between adjacent input pairs shorted together for each multichannel device. 9. Each channel. 10. Standard parts receive 100% testing at 25C (Subgroups 1 and 9). SMD, Class H and Class K parts receive 100% testing at 25, 125, and -55C (Subgroups 1 and 9, 2 and 10, 3 and 11, respectively). 11. Parameters are tested as part of device initial characterization and after design and process changes. Parameters are guaranteed to limits specified for all lots not specifically tested. 12. Propagation delay skew is defined as the difference between the minimum and maximum propagation delays for any given group of optocouplers with the same part number that are all switching at the same time under the same operating conditions. 13. The HCPL-6430, HCPL-6431, and HCPL-643K dual channel parts function as two independent single channel units. Use the single channel parameter limits.
Figure 1. Typical Logic Low Output Voltage vs. Logic Low Output Current.
Figure 2. Typical Logic High Output Voltage vs. Logic High Output Current.
Figure 3. Typical Output Voltage vs. Input Forward Current.
Figure 4. Typical Diode Input Forward Current Characteristic.
9
PULSE GEN. tr = tf = 5 ns f = 500 kHz 25 % DUTY CYCLE IF INPUT MONITORING NODE 100 C1 15 pF GND D.U.T. VCC
VCC
VO OUTPUT MONITORING NODE
5.0 V
1.3 K 0.1 F
30 pF C2 2.5 K
THE PROBE AND JIG CAPACITANCES ARE REPRESENTED BY C1 AND C2.
ALL DIODES ARE 1N4150 OR EQUIVALENT.
Figure 5. Test Circuit for tPLH, tPHL, tr, and tf .
Figure 6. Typical Propagation Delay vs. Ambient Temperature.
Figure 7. Typical Propagation Delay vs. Input Forward Current.
PULSE GENERATOR ZO = 50 tr = tf = 5 ns 1 IF 2 3 4 INPUT VE MONITORING NODE
D.U.T. VCC 8
VCC
5.0 V S1 0.1 F
7 6 GND 5
VO C1 30 pF
D1
1.3 K
D2 2.5 K D3 D4 S2
Figure 8. Test Circuit for tPHZ, tPZH, tPLZ, and tPZL . (Single Channel Product Only).
10
Figure 9. Typical Enable Propagation Delay vs. Ambient Temperature. (Single Channel Product Only).
t P S K
Figure 10. Propagation Delay Skew, tPSK , Waveform.
IF B D.U.T. VCC A + VFF - GND
VCC = 5.0 V
0.1 F*
OUTPUT VO MONITORING NODE
CL 15 pF VCM + - PULSE GEN.
D.U.T.* VCC IO 100 TYP. 100 GND VDC = 3.0 V ICC 0.01 F VCC = 5.25 V IF + -
VIN 2.1 V
CONDITIONS: IF = 10 mA IO = 25 mA TA = +125 C * FOR SINGLE CHANNEL UNITS, GROUND ENABLE PIN.
Figure 11. Test Diagram for Common Mode Transient Immunity and Typical Waveforms.
Figure 12. Operating Circuit for Burn-In and Steady State Life Tests.
11
MIL-PRF-38534 Class H, Class K, and DSCC SMD Test Program
Agilent Technologies' Hi-Rel Optocouplers are in compliance with MIL-PRF-38534 Classes H and K. Class H and Class K devices are also in compliance with DSCC drawings 596289570, and 5962-89571. Testing consists of 100% screening and quality conformance inspection to MIL-PRF-38534.
Data Rate and PulseWidth Distortion Definitions
Propagation delay is a figure of merit which describes the finite amount of time required for a system to translate information from input to output when shifting logic levels. Propagation delay from low to high (tPLH) specifies the amount of time required for a system's output to change from a Logic 0 to a Logic 1, when given a stimulus at the input. Propagation delay from high to low (tPHL) specifies the amount of time required for a system's output to change from a Logic 1 to a Logic 0, when given a stimulus at the input (see Figure 5).
When tPLH and tPHL differ in value, pulse width distortion results. Pulse width distortion is defined as |tPHL - tPLH| and determines the maximum data rate capability of a distortionlimited system. Maximum pulse width distortion on the order of 25-35% is typically used when specifying the maximum data rate capabilities of systems. The exact figure depends on the particular application (RS-232, PCM, T-1, etc.). These high performance optocouplers offer the advantages of specified propagation delay (tPLH, tPHL), and pulse width distortion (|tPLH -t PHL|) over temperature and power supply voltage ranges.
Applications
VCC1 = +5 V 226 DATA IN A 30 pF HCPL-5400 VCC 274 0.1 F
TTL LSTTL STTL HCMOS
VCC2 = 5 V
DATA OUT Y
GND 1 1 TOTEM POLE OUTPUT GATE (e.g. 54AS1000) Y=A
GND GND 2
2
Figure 13. Recommended HCPL-5400 Interface Circuit.
VCC1 = +5 V HCPL-5400 DATA IN A 464 STTL TTL LSTTL STTL GND 1 OPEN COLLECTOR OUTPUT GATE (e.g. 54S05) Y=A GND 2 DATA OUT Y VCC 0.1 F VCC2 = 5 V
GND 1
2
Figure 14. Alternative HCPL-5400 Interface Circuit.
226 VCC1 = 5 V DATA IN A TOTEM POLE OUTPUT GATE (e.g. 54AS1000) DATA IN A GND 1 1
30 pF HCPL-5430
274
VCC
0.1 F
TTL LSTTL STTL HCMOS
VCC2 = +5 V
TTL LSTTL STTL HCMOS
DATA OUT Y DATA OUT Y
274 GND Y=A 226 30 pF
GND 2 2
Figure 15. Recommended HCPL-5430 and HCPL-6430 Interface Circuit.
VCC1 = +5 V DATA IN A STTL OPEN COLLECTOR OUTPUT GATE (e.g. 54AS05) DATA IN A
464 HCPL-5430 VCC 464 0.1 F
TTL LSTTL HCMOS STTL
VCC2 = +5 V
TTL LSTTL HCMOS STTL
DATA OUT Y DATA OUT Y
GND Y=A GND 1 2 1 GND 2
Figure 16. Alternative HCPL-5430 and HCPL-6430 Interface Circuit.
www.semiconductor.agilent.com Data subject to change. Copyright (c) 2000 Agilent Technologies April 1, 2000 Obsoletes 5968-0405E 5968-9403E
This datasheet has been download from: www..com Datasheets for electronics components.

▲Up To Search▲

Price & Availability of 5962-8957103KPA

	To Download 5962-8957103KPA Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .